With automatic transmission, people can complete the driving of the car between the throttle and the brake. It is very easy. If the owner neglects to maintain the automatic transmission, the delicate automatic transmission is prone to malfunction.
Tip 1 :When the wrecker is parked for a long time, the shift lever is still hung in the D range .
While waiting for a signal or traffic jam, if the time may be within a minute change in the bar holder block D, but a long time, the best gear change into the N (neutral), and tighten the parking brake, otherwise The oil temperature of the transmission is increased, and the oil is easily deteriorated.
Tip 2 :When driving at high speed or downhill, shift the gear lever to slide in the N range .
Some of the driver to conserve fuel at high speeds or downhill, the shift lever to N sliding block, which is likely to burn transmission. When the long slope is actually required to slide, the shift lever can be kept in the D block, but the engine can not be turned off.
Tip 3 :The engine is started in the gear outside the automatic transmission P or N.
Other than P or N range to start the engine, the engine can not operate, but it may burn transmission neutral start switch. Therefore , the engine can only be started in P or N range. Before starting the engine, make sure that the shift lever is in P or N range .
Tip 4 :The parking brake is not used when the ramp is parked.
When parking on the slope, there is a potential safety hazard if the parking brake is not used. Although the parking lock mechanism provided in the P position of an automobile equipped with an automatic transmission is generally seldom ineffective , it may cause accidents if it fails. .
Tip 5 :As long as D block starts, you can increase the throttle to shift to high speed .
This practice is wrong. Because the shift operation should be " advanced ahead of the accelerator, step on the accelerator downshift . " That is, after the start of D block, keep the throttle opening 5% , accelerate to 40km / h , fast loose throttle, can be increased to a gear, and then accelerated to 75km / h , loose throttle can increase a gear . When driving down, press the driving speed and press the throttle slightly to return to the low gear. However, it must be noted that the throttle must not be stepped on. Otherwise, the low gear will be forcibly engaged and the transmission may be damaged.
Hubei Chengli Special Purpose Vehicle Co., Ltd.  Address: Chengli Automobile Industrial Park, South Suburb of Suizhou City, Hubei Province  Â
  Sales Manager : Manager Zhang   Mobile Phone: 18727982266  0722-3325000    Fax: 0722-3324444
Plastic Injection Insert Molding
1. The combination of the easiness of molding and bending of resin and the rigidity, strength and heat resistance of metal can make complex and sophisticated metal-plastic integrated products sturdily.
2. In particular, the combination of the insulation of resin and the electrical properties of metal can meet the basic functions of electrical products.
3. The pre-forming combination of multiple inserts makes the post-engineering of product unit combination more reasonable.
4. Insert products are not limited to metal, but also cloth, paper, wire, plastic, glass, wood, wire ring, electrical parts and so on.
5. For rigid parts and flexible parts on rubber sealing pad, the complex operation of arranging sealing ring can be eliminated after the integrated products are made by injection molding on the matrix, which makes the automatic combination of the following process easier.
6. Because it is the fusion of molten material and metal insert, compared with the pressing molding method, the metal insert gap can be designed to be narrower, and the reliability of composite product molding is higher.
7. Suitable resin and molding conditions may be used for sealing and fixation of susceptible products such as glass, coils, electrical parts, etc.
8. Inserts can also be completely sealed into the resin by selecting the appropriate mold construction.
9. After the insert is molded, it can also be made into a product with hollow grooves along with the core hole.
10. The combination of vertical injection molding machine and manipulator, the whole row device of insert products, etc., the insert forming engineering can be mostly automated production.
Plastic Injection Insert Molding,Washing Machine Plastic Injection Moulds,Plastic Injection Molding,Plastic Injection Molding Machine
Suzhou Dongye Precision Molding Co.,Ltd. , https://www.sjinjectionmolding.com