· The maximum fine for violation of Shenzhen Airport from next week can reach 3,000 yuan

The reporter was informed yesterday that the Shenzhen Traffic Police decided to set up the second strict management zone in the surrounding area of ​​Shenzhen Airport, and designated some sections of the strict control zone as busy traffic sections.
From March 16th, the fines will be increased, and the roads around the airport area will be penalized with a minimum penalty of 500 yuan. If the emergency lane is occupied in a non-emergency situation, it will be punished by 3,000 yuan.
The key sections of the airport area were designated as busy traffic sections, raising the fines and enabling monitoring equipment to capture penalties. The traffic sections delineated this time include: Guangshen Expressway, South Square of Hezhou Toll Station, South Airport Road (including auxiliary road), Airport 8 Road, and the entire section of the pilot viaduct. In addition to the upper and lower passengers (ie, stop and go), the above-mentioned road sections will strictly investigate and deal with motor vehicle violations. At the same time, the monitoring device settings are encrypted to achieve full coverage of the above-mentioned road segments, and automatic capture of the violation behavior.
In the event of a road violation outside the busy road section mentioned above, it shall be ordered to leave immediately, and the person who refuses to leave shall be punished after obtaining evidence according to law. If the illegal vehicle interferes with the passage of other vehicles or pedestrians, it shall be towed to the designated place for parking according to law. In addition, the traffic police department will add a broadcast in the video surveillance area of ​​the airport area, and provide a voice warning to the illegal vehicles and order them to leave immediately.
How to punish airport violations?
According to the provisions of Article 10 of the Regulations on Punishment of Road Traffic Safety and Violation in Shenzhen Special Economic Zone, the Shenzhen Municipal Transportation Department imposed penalties on 500, 1000 and 2000 yuan for violations of roads around the airport area. In the case of two or more situations at the same time, the punishment shall be imposed in accordance with the principle of “high or low”.
A fine of 1000 on a busy section of traffic, or a fine on a sidewalk, crosswalk, yellow square, or bus stop on a non-traffic section, or on the departure of the pilot viaduct departure platform exceeding the time indicated by the sign. yuan.
A fine of 500 yuan will be imposed on the roads outside the busy traffic sections above.
Traffic accidents caused by violations shall be liable for accidents according to law; roads blocked due to violations, causing other vehicles to be unable to pass; violations in busy traffic sections, disobedience to management, refusal to leave immediately; the same car, If one of the roads in the area around Shenzhen Airport violates within one year and has been recorded (punished) three times or more, it will be fined 2,000 yuan.
Due to objective reasons such as failures and accidents, the highway was also fined 2,000 yuan, but in the case of non-emergency use of emergency lane parking, a fine of 3,000 yuan and a score of 6 points were imposed.

Standing Seam aluminum roof panel roll forming machine for India market is the special equipment for continuous rolling and cold-forming on steel sheet. It adopts Pre-painted, galvanized, or aluminum steel sheet as the raw material, decoiler, feeding and leveling machine, main roll forming machine, hydraulic cutting to the size and specification according to customer's requirements, and output the finished panels. This machine adopts PLC control, AC frequency and adjusting the speed technology, and it realizes the continuous automatically production, therefore, it is really a new type of energy-saving and high-effective producing equipment for steel structure. 

Specifications:

Decoiler - Feeding guide - Main roll forming machine - PLC control system - Hydraulic cutting - Receiving table

Pictures for machine:

Training and Installation :
1. We offer installation service local in paid, reasonable charge. 
2. QT test is welcome and professional.
3. manual and using guide is optional if no visiting and no installation. 


Certification and after service:
1. Match the technology standard, ISO producing certification 
2. CE certification 
3. 12 months warranty since the delivery. Board. 


Our advantage:
1. Short delivery period. 
2. Effective communication 
3. Interface customized. 

Standing Seam Roll Forming Machine

Standing Seam Roll Forming Machine,Standing Seam Roof Roll Forming Machine,Jch Standing Seam Roll Forming Machine,Plc Standing Seam Roll Forming Machine

YingYee Machinery and Technology Service Co.,Ltd , http://www.yingyee.cn